NT2310 Ethernet Analog Output Modules from Acromag

NT2310 Ethernet Analog Output Modules from Acromag
The BusWorks® NT2000 series offers a cost-effective, modular solution for Ethernet remote I/O systems. Two module types are available. NTE Ethernet models provide the protocol interface plus I/O signal processing channels. NTX expansion modules add extra I/O channels when mated to any NTE Ethernet communication module.

NT2310 modules offer 8 current outputs. Each output is driven by a 16-bit DAC. NTE Ethernet models provide a compact network interface to control 4-20mA loops. Appending NTX expansion models can interface up to 32 current outputs at a single IP address.

Applications include controlling analog actuator levels and driving recorders, displays, or other instruments. The outputs can control valves, pumps, and motors to regulate flow, level, or temperature.

An isolated RS-485 bus links up to three expansion modules to the Ethernet module with connectors that join along the DIN rail. This internal NT bus distributes power and communication between the modules. Users can mix analog, temperature, and discrete I/O modules across the NT bus.

Acromag’s i2o® messaging technology allows direct peer-to-peer or multicast communication between remote modules without a master controller.

NT2310 Ethernet Analog Output Modules Features:

  • ​8 process voltage outputs
  • Ethernet I/O plus Expansion I/O
  • Multi-protocol support

NT2310 Ethernet Analog Output Modules Benefits:

  • Configured over Ethernet with web browser
  • Expandable I/O capacity, up to 56 I/O channels of mixed signal types at one IP address
  • Field-selectable Modbus TCP/IP, EtherNet/IP, or *Profinet communication
  • i2o peer-to-peer or multicast communication
  • Dual RJ45 ports enable daisy chain topology
  • Eight current outputs with 16-bit D/A resolution
  • Selectable 0-20mA or 4-20mA output range
  • LED status indicators for visual troubleshooting
  • *OPC-UA, *MQTT and *RESTful API IIoT support
  • Conditional logic for rule-based I/O operation
  • Advanced *alarm and *data logging functions
  • 1500V isolation between I/O, network, and power
  • Thin 25mm housing with pluggable terminals
  • Wide temperature operation (-40 to 70°C)
  • CE compliant. UL/cUL Class 1 Div 2 and ATEX/IECEx Zone 2 approvals (pending)

NT2310 Ethernet Analog Output Modules Specifications:

  • Ethernet Interface (NTE models only)
    • Communication:
      • Configurable for Modbus TCP/IP and EtherNet/IP.
      • Profinet support coming soon.
      • 10/100Mbps data rate, auto-sensing.
    • IP Address
      • Default Configurable static IP or DHCP.
  • Analog Outputs
    • A/D Converter
      • Eight current output channels driven by an octal 16-bit voltage DAC. Outputs share a return.
    • Output Current Ranges
      • Select 0-20mA or 4-20mA DC.
      • Maximum current is 22.6mA.
    • Output Accuracy
      • Factory calibrated to better than ±0.1% of span. Manual calibration of current outputs can improve accuracy to better than ±0.05%.
    • Output Temperature Drift
      • Better than ±60ppm/°C (±0.0060%/°C).
    • Output Load Resistance Range
      • 0‐600 ohms.
    • Output Excitation
      • Two separate excitation inputs, one for 12V power sources (10-15V) and one for 24V power (20-28V). Both excitation sources are diode‐coupled allowing redundant excitation supplies.
    • Output Compliance
      • 12.5V typical (with a 15V internal excitation rail). Output can typically drive 20mA full-scale into 625 ohms, or 22.6mA maximum into 550 ohms.
    • Output Update Rate
      • Outputs update when written and are continuously refreshed every 5 seconds.
  • General I/O
    • Input Update/Conversion Rate
      • Fresh data available to the network every 10ms. Dependent on number of samples with averaging.
    • Response Time from an Ethernet command
      • Less than 5ms, typical.
  • Environmental and Physical
    • Temperature and Humidity
      • Operating: -40 to +70°C (-40 to +158°F).
      • Storage: -40 to +85°C (-40 to +185°F).
      • Relative Humidity: 5 to 95%, non-condensing.
    • Isolation
      • 1500V AC for 60 seconds and 250V AC or 354V DC continuous between I/O channels (group), each network port and power circuits.
    • Power Supply
      • 10-32V DC SELV power wired to NTE model only.
      • Power to NTX models is via NT bus connection.
      • Excitation Voltage: +12V DC to +24V DC
    • Power Consumption
      • NTE2311: 1.091W typical, 1.20W maximum.
      • NTX2311: 0.092W maximum (each).
    • Dimensions (width x height x depth)
      • NTE: 25 x 116.9 x 139.2 mm (0.98 x 4.6 x 5.48 inches).
      • NTX: 25 x 116.9 x 116.65 mm (0.98 x 4.6 x 4.59 inches).
    • Weight
      • NTE: 0.5 lbs (0.23 kg).
      • NTX: 0.3 lbs (0.14 kg).
  • Standards and Certifications
    • Electromagnetic Compatibility (EMC)
      • CE marked, per EMC Directive 2004/108/EC.
    • Safety Approvals
      • UL/cUL: Class I; Div 2; Groups A, B, C, D (pending).
      • ATEX/IECEx: Zone 2 (pending)

Download NT2310 Ethernet Analog Output Modules Datasheet

Call us today at (855) 737-4714 to learn more, or fill out our online form and someone will get back to you.

Motion Control and Automation
A lesson for me is that I need to involve you earlier in the program.

You were tireless in your support and it will not be forgotten!

Valin Was There For Us
When we needed technical assistance and applications support, Valin was there for us. Their knowledgeable engineers saved us an invaluable amount of time, helping us get up and running quickly. We are very happy with their services.